An introduction to
THAI ROSEWOOD FURNITURE ORIENTAL DESIGN
The furniture is made by Rosewood which is a common Western name of FA-LEE as called by the Chinese. The common local name is PRADU or PRADUAK
It has the same GENUS as the PALISANDER or BRAZILIAN ROSAWOOD but different species.
COUNTRY OF ORGIN: THAILAND
Rosewood is a high class wood for furniture, it has beautiful grains, very stable and durable, quite expensive and increasingly rare.
TREATMENT OF MOIOSTURE CONTENT INROSEWOOD
With the aid of modern technology, the wood is kiln dried with hot boiling steam for about 21 days in the chamber. The moisture content in the wood is brought down to about 5-6% equilibrium moisture content, but since the relative humidity in Thailand is about 80% throughout the year, moisture will tend to escape back in to the wood while it is in production and the moisture content in the finished good before export is about 10%which is internationally acceptable.
However in parts of the world where heater is used in the house extensively, we recommend that they should control the moisture content in their house to be at least 30-40% by using a humidifier, otherwise when the moisture in the air is below 10%,the moisture that is still in the wood will dry out and cause shrinkage.
The production of Rosewood furniture oriental style can be devided mainly into two sections.
- The preparation of raw materials, by using modern technology and machinery, the parts of each individual joints are cut, this section consume about 30% of the total production work.
- Assembling or carpentry work, after all parts are ready from the machine, it will be assemble mainly by handwork which take longer time and this is where the skill of true craftsmen are required
“The Chinese three-way mitred double locking mortise and tenon with floating panel” would horrify a furniture production engineer because of extreme difficulty in mass producing it. The floating panel is cut from a single piece of wood usually about 9 mm. In thickness and is tongued and grooved into the rails. To support it and prevent any tendency to curl, transverse braces are dovetail grooved into the underside and then tenoned into the long rails of frame. This assembly is found in all panels, be they table tops, door panels or seat frames.
High speed routers are used to rough cutting after the carving designs were prepared by the master, but from then on, all the carving work is done by hand with carving gouges and chisels.
The impeccable lacquer finish
The manufacturers of Rosewood furniture oriental design have been using the centuries old Chinese predecessor – NATURAL LAQUER. It might take a little longer to apply, but it is much deeper and more beautiful than synthetic equivalents.
NATURAL LACQUER is an exudate from the “Lacquer tree “ which is indigenous to China. It is collected in much the same way as latex, is partially evaporated in the sun, and is very expensive
After the final scraping and shaping of the first coarse sanding, a lacquer-based filler is applied to fill the characteristic open grain of Rosewood. This takes eight hours to dry. The furniture is again sanded and a second application of the filler is made which is in turn sanded when dry, with successively finer grade abrasives. The first layer of lacquer is then applied to seal the grain. After sanding with flour paper, if the color of the wood is to be changed, aniline dye is painted on and rubbed down. Then the polishing begins with successive application of clear lacquer. This will be after a minimum of four coating, a total of seven applications of lacquer.
The finish that results from all this hard work has some remarkable properties, not only is it heat–proof, but it is not permanently marked by a wet glass or hot wet pan. The surface is not as hard as a Polyurethane lacquer, but small scratches will polish out.
Above all, the natural quality of the finish allow it to mature with age and wear, so that when the products of today become the antiques of the future, the sun – bleached gold of Rosewood will be enhanced by the patina of the natural lacquer.
Product Quality Quarantee:
The carving and the mother of pearl inlaid are all handmade.
Our Products made from rosewood 100 % from Thai, Lao and Burmese.
All products made from Thailand origin.
The color of the wood can be a little change after a long time (5-10 years). It depends on the maintenance.
The furniture should be kept away from the sunlight and water. Periodically the furniture you may use a soft cloth and you may apply furniture wax 2-3 times a year, furniture wax is recommended.
Do not put the hot or cold products direct to the furniture.Our furniture do not use the finishing paint resists water stains and cigarette burns.
We use the chinese lacquer tree for the natural rosewood color.
We do not use synthetic lacquers.
We do not use plywood.
We use old rosewood.
We only use the screws very limited spots which need to be seperated for transportation.
We can change the sizes that you want but the price may be add up that depend on your design or your size.
We recommend you to purchase the mother of pearl inlaid because the shipping and packing cost will be equal in same items and the furniture will more valuable. You only pay a little more.
An Introduction for Thai Language
siphyafurniture.com, Inc.? 2000 All rights reserved.